ARRMA 1/5 Kraton/Outcast 30T M1.5 Spur Gear by GPM MAKX030TS  [MAKX030TS]

Price:
USD$16.90
Brand:
GPM
Model:
MAKX030TS
GTIN:
4894538416794
Condition:
Brand New
Write a review

GPM MAKX030TS 30T Spur Gear overview

This GPM MAKX030TS is an RC-scale spur gear intended as a direct aftermarket replacement for ARRMA 1/5 Kraton and Outcast platforms. The part is specified as a 30-tooth spur gear with M1.5 tooth module manufactured in 20CrMnTi steel, a grade selected for improved wear resistance and bending strength compared with softer stock alloys.

Designed for high-power 8S BLX brushless setups, the gear serves a drivetrain role where durability and consistent tooth engagement matter for long runs and heavy loads. Installation requires matching the module (M1.5) and checking pinion/spur mesh and shimming; it replaces the factory reference numbers listed below.

Packing includes

  • Spur Gear 30T Mod 1.5 - 1pcs

Original Name / Part No:

ARA310920?ARA311051

Compatible Models

  • ARRMA 1/5 Kraton 4X4 8S BLX Brushless Speed Monster Truck RTR-ARA110002 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 4WD 8S BLX Stunt Truck RTR-ARA5810 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Kraton 8S EXB 4X4 Roller Brushless Speed Truck-ARA5208 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Kraton 4X4 8S BLX EXB Brushless Monster Truck RTR-ARA5808V2 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 8S EXB 4X4 Roller Brushless Stunt Truck-ARA5210 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Outcast 4X4 8S BLX EXB Brushless Stunt Truck RTR-ARA5810V2 (Original Spur Gear 47T/M1.0)

Use this 20CrMnTi steel 30T M1.5 spur gear where a stronger RC-scale replacement is required, confirm module and mesh during fitment, and inspect drivetrain alignment after installation.

What material is this spur gear made from?

The gear is specified as 20CrMnTi steel, chosen for improved wear resistance and toughness in RC drivetrains.

Which tooth module does this part use?

This spur gear is M1.5 module, 30-tooth; ensure your pinion matches M1.5 before fitting.

Does it replace the factory ARRMA part numbers?

The part is offered as a replacement for the factory references listed in the original name block above.

Any installation tips for mesh and alignment?

Match module, set correct pinion-to-spur mesh, check for side load and shaft runout, and retest after a short run-in.

Is this suitable for 8S BLX power setups?

The material and design target higher-stress RC drivetrains such as 8S BLX configurations, but verify overall drivetrain condition and compatibility first.

Will I need additional parts to fit this gear?

Typically no extra parts are required if your vehicle uses M1.5 spur/pinion geometry, but check gear height and any required shims during installation.

Copyright © 2008-2026 rcjaz.com All rights reserved