TRAXXAS Slash 4X4 Low-CG 7075 Alloy Front C Hub by GPM SLA019N  [SLA019N]

TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N
Price:
USD$28.90
Brand:
GPM
Model:
SLA019N
GTIN:
4894538387933
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"

Front C hub for Slash 4X4

This GPM SLA019N front C hub is an RC-scale replacement part designed for TRAXXAS Slash 4X4 and several related 1/10 4WD platforms. Machined from 7075 alloy, it locates the knuckle arm on a bearing instead of a shaft hole to reduce play and promote smoother steering feedback. Multiple upper tie rod mounting holes let you fine-tune steering roll center and toe characteristics without changing other suspension parts.

Installation follows the stock mounting points at the front c-hub area and uses the supplied hardware for a direct swap. The bearing-mounted knuckle location requires correct bearing seating and typical thread-lock on the metal screws where applicable. This part is intended for hobby RC use only and is compatible with the models listed below.

Packing includes

  • C-Hub - 1pcs
  • King Pin - 1pcs
  • Grade 12.9 black Round Head Screws 3x14 - 1pcs
  • Grade 12.9 black Round Head Screws 3x16 - 1pcs

Original Name / Part No:

6832

Compatible Models

  • TRAXXAS-SLASH 4X4 LOW-CG-68086-21
  • TRAXXAS 1/10 RUSTLER 4X4 VXL-67076-4
  • TRAXXAS 1/10 4WD HOSS 4X4 VXL 3S-90076-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74064-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74054-4
  • TRAXXAS 1/10 Rustler 4X4-67064-1
  • TRAXXAS 1/10 Rustler 4X4-67064-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68086-4
  • TRAXXAS 1/10 Slash 4X4-68054-1
  • TRAXXAS 1/10 Slash 4X4-68054-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68286-4
  • TRAXXAS 1/10 Stampede 4X4 VXL-67086-4
  • TRAXXAS 1/10 Rustler 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-68277-4

Use this front C hub to tighten front-end steering feel and reduce knuckle slop; adjust upper tie rod positions to dial in steering response for track or off‑road setups, and verify bearing seating and screw torque during installation.

Will this part fit my Slash 4X4 VXL?

This part lists compatibility with multiple Slash 4X4 VXL variants shown in the Compatible Models block; check your chassis code against that list before ordering.

Do I need bearings or other parts not included?

The package replaces the C hub hardware shown, but you should verify existing wheel bearings and knuckle bearings are serviceable; the hub uses a bearing-mounted knuckle so correct bearing fit is required.

What tools and thread locker should I use for installation?

Use the appropriate hex driver for the supplied screws and apply a small amount of medium-strength thread locker on metal-to-metal fasteners where recommended by your chassis manual.

How does the 7075 alloy affect steering feel?

7075 alloy provides higher tensile strength and rigidity compared with standard alloys, which can reduce flex in the front end and produce crisper steering feedback when combined with proper geometry tuning.

Copyright © 2008-2026 rcjaz.com All rights reserved