TRAXXAS SLASH 4X4 Low-CG Aluminium Main Shaft by GPM SLA025LCG  [SLA025LCG]

TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG
Price:
USD$19.90
Brand:
GPM
Model:
SLA025LCG
GTIN:
4894538078329
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"

Low‑CG aluminium main shaft for Slash 4X4

This aftermarket main shaft is an RC-scale replacement part produced by GPM for the TRAXXAS SLASH 4X4 platform, supplied as a 1 pc set. The design pairs an aluminium shaft body with hardened steel end fittings to balance reduced rotating mass with wear resistance at contact points.

Fit and installation are straightforward for hobbyists familiar with Slash 4X4 driveline service: remove the original shaft from the gearbox or output assembly, inspect splines and bearings for wear, and install the GPM shaft using the original retaining hardware. No special tools beyond standard hex drivers and basic shop supplies are required.

In tuning terms this low‑CG shaft helps lower rotating mass concentration while the hardened steel ends preserve interface durability, making it useful when aiming for smoother driveline response and longer service intervals in off‑road use and club‑level tuning setups.

Specifications

  • Item Main Shaft
  • Material Aluminium body with hard steel ends
  • Model Number SLA025LCG
  • Compatibility TRAXXAS SLASH 4X4
  • Quantity 1 pcs

This GPM main shaft is intended as a direct replacement for Slash 4X4 drivetrains where reduced rotating mass and reinforced bearing interfaces are desired; verify spline and retaining hardware compatibility before final installation.

Is this shaft compatible with all TRAXXAS Slash 4X4 variants?

It is intended for TRAXXAS SLASH 4X4 models referenced by the product title; confirm spline and retention type match your vehicle before fitting.

Do I need new bearings when installing this shaft?

Inspect existing bearings for play or damage and replace as needed; fresh bearings ensure correct alignment and reduce premature wear.

What tools are recommended for installation?

Basic hex drivers, a bench vise or soft‑jaw pliers for light press fits, and thread locker for retention screws where applicable.

How should I maintain the aluminium shaft and steel ends?

Keep contact areas clean, inspect for wear periodically, and apply light lubricant to reduce corrosion on steel ends if the model is used in wet conditions.

Copyright © 2008-2026 rcjaz.com All rights reserved